Super stereo digital echo by KT5211P

This stereo digital echo project is circuits pioneering in the use of the old echo circuit before using the IC-BBD to the digital system. By using a digital echo circuit IC designed especially for the heart to work.

This circuit is designed as a stereo system, to make it easy, and easy to-use applications, with your amplifier, followed circuit below.

Be seen from the circuit, is quite simple consists of the main equipment are 4 transistor and 5 ICs only.

The working of this circuit
The left channel input signal is entered pass through capacitor C1 to base pin of transistor Q1(2SC1815). Which is an input amplifier has a sufficient strength that enter to other next circuit section.

The switch S1 is defined gain ratio of circuit suitable for input. When switch turn on , will be have high gain, For a record player or a micro phone or an input signal with low signal strength.
Then we turn off switch S1 will be has low gain for the input signal with a high signal, such as a tuner or tape player or CD player etc.
The output signal from collector pin of Q1 is entered into C3 then split into 2-way
– The first way will be enter directly through the R41 to emitter of transistor of Q3 To include with signs through the delay signal circuit, until there is signs at collector pin through C22 to output L channel.
– The output signal of Q1 another way will be entered through to R7 signal delay circuits consisting of IC1, IC3, IC4.

VR1 use to adjusts the input signal that is input to delay circuit has high strength.
VR4 used to fine frequency of clock signal. If you fine frequency to lower, the voice repeated will distance a range but high frequency Audio is faster iterative, stacked, like an echo signal.

The output from IC1 at pin 34 will be through to C18 and VR5 to base pin of transistor Q3 for mixed with the direct signal has output is digital echo as you need.

The some output from IC1 will be pass to R22 and VR1 feed back to input of IC1 makes has The sound duplicate If we fine VR1 to have a lot of feedback signal will have many repetitive sound. Be very much careful not to adjust, so that the oscillation.
The work of right channel circuits same as the left channel, as described above.

Creation and customize circuits.
Creation and customize this circuits. Much easier because you do not need to tune circuits. Just included according to the circuit all devices on the PCB as shown only.

The detail parts.
IC1_____________________________KT5211P
IC2_____________________________393S
IC3_____________________________4164 (41256)
IC4_____________________________KT4469
IC5_____________________________LM7812
IC6_____________________________LM7805
Q1, Q2, Q3, Q4___________________C1815
D1, D2__________________________1N4148
D3______________________________DB101
Z1______________________________ZENER 3V9
R1, R14, R33_____________________1M
R2, R12, R34_____________________220K
R3, R11_________________________220ohm
R4, R7, R8, R10__________________120K
R5, R9__________________________1.5K
R6, R13, R20, R22, R27, R28, R38___10K
R15, R21________________________33K
R16____________________________20K
R17____________________________51K
R18____________________________39K
R19____________________________2.2K
R23, R32________________________12K
R24, R31________________________30K
R25, R30________________________500ohm
R26, R29________________________330K
R35____________________________1K
R36____________________________7.5K
R37____________________________15K
R39, R40, R41, R42_______________5K
C1, C2, C5, C6, C22, C23__________10uF 16V
C3, C4, C7, C10, C18, C21, C24, C25_1uF 50V
C8____________________________0.0018uF 50V
C9____________________________680pF
C11___________________________4.7uF 16V
C12, C26, C27__________________0.01uF 50V
C13___________________________47uF 16V
C14, C15, C28, C31, C33, C34_____0.1uF 50V
C16___________________________0.47uF 50V
C17___________________________0.0068uF 50V
C19, C20_______________________0.047uF 50V
C29___________________________1000uF 25V
C30___________________________470uF 10V
C32___________________________470uF 16V
T1_____________________________15-0-15V SEC.
L1 (INDUCTOR)_________________100uH.

Installation to use.
The following applications can be connected as follows.
1. Connect the output of digital echo to input of stereo.
2. Connect input of digital echo to input signal( REC).
3. Turn off tape monitor at OFF
For a player to MIC, and the output of this project. To the input of the amplifier to the tuner or AUX. Directly.

Comments are closed.