Archive for category: Battery and Charger Diagram

Circuit Calibrated Current For Battery Charger

Battery and Charger Diagram | By: Diagram mania

Circuit Calibrated Current For Battery Charger. Power Supply Voltage Input Calibrated.

NiCad Discharger for Tx & Rx Packs

Battery and Charger Diagram | By: Diagram mania

Parts List: Resistors: 10K(7), SOT 16K4 & 6.9K, 470 Ohm(2), 4K7(2), 1K(3), 47 ohm/5W, 47ohm(2 parallel). Capacitors: 10uF (electrolytic), 0.1uF (ceramic). Transistors: BD681(2), BC548(1) Diodes: 1N4001(2) Led’s: Red, 5mm(2) IC: LM3900, 14pin, plus 14-pin socket Switches: Momentary, push-on(2) The Care and Feeding of NiCad Batteries: The reason I designed this discharger are many, however I […]

USB port AA NiMH and NiCd Battery Charger by IC 393

Battery and Charger Diagram | By: Diagram mania

I Find circuit Chartger battery AA NiMH for USB port. I see to Good WEB : http://www.stefanv.com/electronics/ Detail : In a recent blog entry, I complained about all the chargers and wall warts I need to carry with me when going on a trip. This project, which can charge a pair of AA Nickel Metal […]

USB Li-ion battery charger by MCP73861

Battery and Charger Diagram | By: Diagram mania

This is a charger for lithium ion batteries which takes its power from the USB port of a computer. It uses the MCP73861 or MCP73863 Li-ion battery charger chip manufactured by Microchip. Read More Source: http://www.instructables.com/id/USB-Li-ion-battery-charger/ Thank you.

iPOD – MP3 Player Charger by MC34063

Battery and Charger Diagram | By: Diagram mania

Portable iPod charger that you can use while away from your computer. The circuit is based around an MC34063 switchmode regulator. This has high efficiency so that there is very little heat produced inside the box, even when delivering its maximum output current. The circuit is more complicated than if we used a 7805 3-terminal […]

Ni-Cd Battery Auto Charger by LM311

Battery and Charger Diagram | By: Diagram mania

To use portable devices such as digital camera, wireless headphone, pocket radio, etc, which they operates with two “AAA” size batteries, using rechargeable Ni-Cd batteries is a conscionable way to reduce cost. Above circuit has been designed to charge automatically two series 350mAh “AAA” size batteries. Set the 20KOhms multi turn potentiometer to get a […]

Solar charger for lead-acid battery by LM339

Battery and Charger Diagram | By: Diagram mania

This circuit is intended for charging lead-acid batteries with a solar panel. The customary diode that prevents the battery from discharging through the solar panel has been replaced by a FET-comparator combination. The charger will stop charging once a pre-set voltage (temperature compensated) has been reached, and recommence charging when the voltage has dropped off […]

Fast NiMH – NiCd Battery charger by PIC16F84A

Battery and Charger Diagram | By: Diagram mania

This battery charger charges a NIMH 5-pack battery used in the BiPed robot in less than 1 hour, and charges the 10-pack NiCd used in the Snuf robot in about 30 minutes. To prevent overheating of the battery, the charging current is turned off when the slope of the battery-voltage turns from positive into negative. […]

USB iPOD Charger by REG1117A

Battery and Charger Diagram | By: Diagram mania

The circuit’s pretty simple, basicly it’s just a voltage regulator. Both the LM317 and the REG1117A (LDO) fit the PCB, maybe there are even more types that I’m aware of that can be used on it. I did add one extra thing: a LED that shows if the connected device is consuming power. To do […]

USB Powered AA NiMH – NiCd Battery Charger by LM393

Battery and Charger Diagram | By: Diagram mania

The charger in this project is designed to charge two AA NiMH or NiCd cells of any capacity (as long as they are the same) at about 470mA. It will charge 700mAh NiCds in about 1.5 hours, 1500mAh NiMHs in about 3.5 hours, and 2500mAh NiMHs in about 5.5 hours. The charger incorporates an automatic […]